- 您现在的位置：买卖IC网 > Sheet目录344 > MSL3082CS (Atmel)IC LED DRIVER 8 STRING
Connecting an LED String Power Supply
to an Efficiency Optimizer
The MSL3082 is designed to control an external LED
string power supply that uses a voltage divider (R TOP and
R BOTTOM in Figure 4) to set the output voltage, and whose
regulation feedback voltage is not more than 1.5V. The
efficiency optimizer improves power efficiency by injecting
a current of between 0 and 45μA into the voltage divider
of the external power supply, dynamically adjusting the
power supply's output to the minimum voltage required
by the LED strings. To select the resistors first determine
V OUT(MIN) and V OUT(MAX) , the minimum and maximum string
supply voltage limits, using:
V OUT(MIN) = ( V f (MIN) *[# ofLEDs ] ) + 0.5 ,
and
V OUT(MAX) = ( V f (MAX) *[# ofLEDs ] ) + 0.5 ,
where V f(MIN) and V f(MAX) are the LED minimum and
maximum forward voltage drops at the peak current
set by R Sn (page 11). For example, if the LED data
are V f(MIN) = 3.5V and V f(MAX) = 3.8V, and ten LEDs are
used in a string, then the total minimum and maximum
voltage drops across a string are 35V and 38V,
respectively. Adding an allowance of 0.5V for the string
drive MOSFET headroom brings V OUT(MIN) to 35.5V and
V OUT(MAX) to 38.5V. Then determine R TOP using:
Figure 4. FBO Connection to Power Supply Voltage Divider
Using Multiple Atmel LED Driver-MSL3082s
to Control a Single Power Supply
Cascade multiple MSL3082 devices into a chain
configuration (Figure 5) with the FBI of one device
connected to the FBO of the next. Connect the first FBO
to the power supply feedback resistor node through a
CMPSH-3 or similar Schottky diode, and the unused FBI
input to ground as close to the MSL3082 as possible.
The chained devices work together to ensure that the
system operates at optimum efficiency. Note that the
accuracy of the feedback chain has the potential to
degrade through each link of the FBI/FBO chain by as
much as 2%. Determine the worst case maximum FBO
R TOP =
V OUT (MAX) _ V OUT(MIN)
I FBO(MAX)
,
current, I FBO(MAX/MIN) , using:
I FBO(MAX / MIN) = 45 μ A * (0.98) N -1 ,
R BOTTOM = R TOP *
V OUT(MAX) _ V FB
where I FBO(MAX) is the 45μ A maximum output current of
the efficiency optimizer output, FBO. Finally, determine
R BOTTOM using:
V FB
,
where V FB is the regulation feedback voltage of the
power supply. Place a Schottky diode (CMPSH-3 or
similar) between FBO and the supply’s feedback node
to protect the MSL3082 against current flow into FBO.
12
where N is the number of MSL3082s connected in
series. Use this result in the above R TOP resistor equation
for the term I FBO(MAX) instead of using the 45μA figure
shown here.
Take care in laying out the traces for the efficiency
optimizer connections. Minimize the FBI/FBO trace
lengths as much as possible. Do not route the signals
close to traces with large variations in voltage or current
because noise may couple into FBI. If these traces must
be routed near noisy signals, shield them from noise by
using ground planes and/or guard traces.
Atmel LED Driver-MSL3082
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MSL3085BT
IC LED DRIVER 8 STRING
MSL3162BT
IC LED DRIVER 16 STRING
MSL3164BT
IC LED DRIVER 16 STRING
MSL3167GU
IC LED DRIVER 16 STRING
MT-6 PLUS
SURGE SUPPR TCHMSTR 6OUT 10'CORD
MT42L256M32D4KP-3 IT:A
IC LPDDR2 SDRAM 8GBIT 168FBGA
MT45W1MW16BDGB-708 AT
IC PSRAM 16MBIT 104MHZ 54VFBGA
MT48H32M16LFB4-75B IT:C
IC SDRAM 512MB 54VFBGA
相关代理商/技术参数
MSL3082CS-R
功能描述:LED照明驱动器 8Str Hi Pwr White or RGB LED Drivers
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL3085
制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-string White and RGB LED Driver with Adaptive Power Control, EEPROM, and I2C/SMBus Serial Interface
MSL3085BT
功能描述:LED照明驱动器 8-Stinge White & RGB LED Dvrs wAdapt Pwr
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL3085BT-R
功能描述:LED照明驱动器 8-String White & RGB LED Drivers with Ad
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL3086-IU
功能描述:LED照明驱动器 8-Str LED Driver Internal Boost Cntr
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL3086-IUR
功能描述:LED照明驱动器 8-Str LED Driver Internal Boost Cntr
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL3088-IU
功能描述:LED照明驱动器 8-Str LED Driver Intrnl Bst Cntr/Phas
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL3088-IUR
功能描述:LED照明驱动器 8-Str LED Driver Intrnl Bst Cntr/Phas
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N